Utilize este identificador para referenciar este registo:
http://hdl.handle.net/10773/26933
Título: | Transmitter for 5G systems |
Outros títulos: | Transmissor para sistemas 5G |
Autor: | Marques, Rúben Pereira |
Orientador: | Cabral, Pedro Miguel da Silva Silva, Adão Paulo Soares da |
Palavras-chave: | 5G OFDM modulation Power amplifier Simulation platform SISO Alamouti 2x1 BER |
Data de Defesa: | 20-Dez-2018 |
Resumo: | The current 4G systems are based on the OFDM modulation which, while
providing great
exibility and intricacy to the multipath propagation inherent
in wireless systems, it has great variations in their temporal envelope
which causes high PAPR and, consequently, obstacles in the PAs performance.
In this sense, the emergence of 5G systems has given rise high
hopes of reducing the above mentioned problems of 4G systems, allowing
more eficient data transmission.
In the simulation of wireless communication system there are two simulation
domains that must be taken into account: the system analysis that allows
the study of diferent modulations and the circuit analysis that, in turn,
allows the study of nonlinear circuits, as is the case of PAs present in these
systems. In this way, it becomes important to unite these two domains
allowing the existence of a unifying simulation tool, which has been called
the simulation platform. With this platform it is possible, besides joining
two domains hitherto analyzed separately, not only to study the behaviour
of a 5G system but also any other system due to its adaptability.
Thus, the system analysis is performed with the help of MATLAB software,
in which three types of digital modulation (QPSK, 16-QAM and 64-QAM
modulation) will be studied along with OFDM modulation. For the circuit
analysis it was used the ADS circuit simulation software, which will analyze
the behavior of two types of PAs (a Class B and a Doherty).
As a way of testing its functioning, the platform simulations were performed
for three diferent con gurations: SISO, SISO in which the PA model was
replaced by a polynomial approximation, and Alamouti 2x1 (particular case
of the MISO con guration). Finally, the tests of functioning of the simulation
platform are nalized with the comparison of the simulations using the
BER Os atuais sistemas 4G são baseados na modulação Orthogonal Frequency Division Multiplexing (OFDM) que apesar de garantir uma grande exibilidade e robustez à propagação multi-percurso inerente aos sistemas sem fi os, possui grandes variações nas respetivas envolventes temporais o que causa um elevado Peak-to-Average Power Ratio (PAPR) e, consequentemente, limitações no desempenho dos ampli cadores de potência (do inglês, Power Ampli ers (PAs)). Neste sentido, o aparecimento dos sistemas 5G têm suscitado grandes esperanças na redução dos problemas mencionados anteriormente, permitindo uma transmissão de dados mais e ficiente. Na simulação de um sistema de comunicações sem fi os há dois domínios de simulação principais que se devem ter em consideração: a análise de sistema que permite o estudo de diferentes modulações e a análise de circuito que, por sua vez, permite o estudo de circuitos não-lineares, como é o caso dos PAs presentes nestes sistemas. Desta forma, torna-se importante unir estes dois domínios possibilitando a existência de uma ferramenta de simulação unifi cadora, à qual se atribuiu a designação de plataforma de simulação. Com a plataforma de simulação consegue-se, além de unir dois domínios até agora analisados separadamente, não só estudar o comportamento de um sistema 5G mas também de qualquer outro devido à sua adaptabilidade. Assim, a análise de sistema é efetuada com o auxílio do software MATLAB, onde são estudados três tipos de modulação digital (modulação Quadrature Phase Shift Keying (QPSK), 16-Quadrature Amplitude Modulation (QAM) e 64-QAM) juntamente com a modulação OFDM. Para a análise de circuito recorreu-se ao software de simulação de circuitos Advanced Design System (ADS), onde se analisou o comportamento de dois tipos de PAs (um Classe B e um Doherty). Como forma de teste do funcionamento da plataforma, foi efetuada a simulação para três confi gurações diferentes: Single-Input Single-Output (SISO), SISO em que se substituiu o modelo do Power Ampli er (PA) por uma aproximação polinomial e Alamouti 2x1 (caso particular da configuração Multiple-Input Single-Output (MISO)). Por último, os testes do funcionamento da plataforma de simulação são fi nalizados com a comparação das simulações recorrendo ao Bit Error Rate (BER) |
URI: | http://hdl.handle.net/10773/26933 |
Aparece nas coleções: | UA - Dissertações de mestrado DETI - Dissertações de mestrado |
Ficheiros deste registo:
Ficheiro | Descrição | Tamanho | Formato | |
---|---|---|---|---|
Documento.pdf | 6.85 MB | Adobe PDF | Ver/Abrir |
Todos os registos no repositório estão protegidos por leis de copyright, com todos os direitos reservados.